Technical Manual Beltone MARQ. Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark
|
|
- Madeline Fletcher
- 6 years ago
- Views:
Transcription
1 Technical Manual Beltone MARQ Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark Service@Beltone.com
2 Table of Contents Description...3 Matrix & product information...4 Part lists Power dome tool...9 Exploded view...10 Wiring diagram...11 Mic cover removal...12 Battery / Battery door removal...13 Housing removal...14 Adding new colour / replacing housing...15 Microphone replacement...16 Testing equipment...17 Testing protocol for HPG & MPG devices...18 Testing the device with test fixture...19 Testing HPG receiver tube only...20 Testing MPG receiver tube only...21 Receiver tube replacement on test fixture...22 Page 2 of 22
3 Description The Marq17 & Marq9 is an occlusion free Mini BTE RIE product which incorporate a new receiver dome system with an inmoulded wax filter. Other characteristics are: Smallest RIE product ever introduced Significant increased available gain expected vs. competitors and other open fittings for Beltone Available in these Models under the EDGE collection tab: Marq17 Open Marq17 Standard Marq17 HP Open Marq17 HP Standard Marq9 Open Marq9 Standard Marq9 HP Open Marq9 HP standard Dual microphone Two Power Levels - Normal Power and High Power Compatible with Solus 2.2 or higher 10A size battery 106/107 hrs of real time usage Coyote 3.1 hybrid No control options (VC, PB, TC) Compatible with existing flex programming system CS63 cable with a fresh 10A battery for programming Field replaceable sports lock. New RIE domes with integrated wax protection + additional wax protection in receiver housing. Comes in 12 colors: Charcoal, Brown, Grey, Light Grey, Beige, Stone, Arctic Ice, Transparent, Dark Metallic, Blue, Purple and Black. The Marq17 & Marq9 design takes advantage of the current popularity of a small housing due to the RIE. The housing will come in optional colors and be changeable and reusable at the dispenser s office. Page 3 of 22
4 Matrix & Product Information MODEL MARQ 17 MARQ 9 MODEL NAME & Confirgurations MQ1762 Open MQ1762 Standard MQ1762 HP Open MQ1762 HP Standard MQ962 Open MQ962 Standard MQ962 HP Open MQ962 HP Standard Data Sheet Doc No Page 4 of 22
5 Part List Description Part No Description Part No C3.1 Coyote Hybrid Bottom Housing with Laser mark (MQ17) Bottom Housing with Laser mark (MQ9) O-ring Mic (Front and back) TM C36 Mic Gasket (Front) Mic Gasket (Rear) Mic Frame Programming contacts Hinge Pin Battery contact positive (+) Battery contact negative (-) WIRE, ESW, AMBER 7x32µ 14MM WIRE, ESW, GREEN 7x32µ 14MM WIRE, ESW, BLUE 7x32µ 14MM WIRE, ESW, RED 7x32µ 8MM WIRE, ESW, GREEN 7x32µ 8MM WIRE, ESW, RED 7x32µ 6MM WIRE, ESW, AMBER 7x32µ 6MM WIRE, ESW, GREEN 7x32µ 6MM WIRE, ESW, RED 7x32µ 7MM WIRE, ESW, AMBER 7x32µ 7MM WIRE, ESW, GREEN 7x32µ 7MM PIN BAG, MARQ REMOVAL TOOL Insulating pad (for hybrid) CONFORMAL COATING,SL1367 Receiver Tube: MPG (Medium Power Gain) TUBE ASM, REC,TEST, STRAIGHT(modified) COUPLER INSERT,DSA (brass) BATTERY PILL, 10A TEST FIXTURE PR.CABLE CS63 STRIP CS63 (10PK) * For coat SL1367, check e.g. vendor website: to **purchase locally Removal Tool * Please find p/n s and pics of the parts used for test on the last pages Page 5 of 22
6 Part List - Receiver & Domes Description DOMES USED WITH NP REC Bag (10 pcs) Blister Pack (8 pcs) DOME,REC,SZ5,SM DOME,REC,SZ7,MDM DOME,REC,SZ10,LGE DOME,REC,TULIP,STD DOME,REC,PWR,SM DOME,REC,PWR,MDM DOME,REC,PWR,LGE Description DOMES USED WITH HP REC Bag (10 pcs) Blister Pack (8 pcs) DOME,REC,PWR,SM DOME,REC,PWR,MDM DOME,REC,PWR,LGE Rec Tube Size NP HP 0L R L R L R L R L R Rec Tube blister pack containing one rec tube Power Domes Sizes L,M,S DOME Sizes L,M,S DOME ST Tulip Page 6 of 22
7 Part List - Accessories Description Part No RECEIVER TUBE REBENDING KIT SPORTLOCKS, BAG (10 pcs) REMOVAL TOOL FILTER DISP, RED, W/ RED FILTER FILTER DISP, BLU, W/ BLU FILTER FLTR,DISP,RED/BLU,HF CUSTOM INSERT TIP, NP INSERT, RIE HP CUSTOM TIP HP RECEIVER CUSTOM INSERT TOOL GASKET, RIE HP CUSTOM TIP WAX REMOVER (USE AS REC REMOVAL TOOL FOR CUSTOM TIP EARMOULD) POWER DOME TOOL KIT (tool & guide) TOOL, POWER DOME, RIE MEASUREMENT TOOL Note: For Custom Insert Option instead of Domes, follow Custom Insert Process Doc posted in the GTO website Tool, power dome Custom insert tips Tool HP rec custom insert NP Gasket RIE HP rec custom insert (to be placed into the custom insert tips) HF3 Filter L/R HF3 Filter (red & blue) HP Meassurement Tool One side for L and the other side for R Page 7 of 22
8 Part List - Housing Parts & Replacement Packs COLOUR HSG TOP MIC COVER BATT DOOR Part Description Part No GREY STONE CHARCOAL BROWN LIGHT GREY BEIGE ARCTIC ICE DARK METAL TRANSP PURPLE BLUE BLACK REPLACEMENT PK,BELTONE 62,GREY N* REPLACEMNT PK,BELTONE 62,STONE N* REPLACEMNT PK,BELTONE 62,CHARC N* REPLACEMNT PK,BELTONE 62,BROWN N* REPLACMNT PK,BELTONE 62,LT GRY N* REPLACEMNT PK,BELTONE 62,BEIGE N* RPLCMNT PK,BELTONE 62,ARCT ICE RPLCMNT PK,BELTONE 62,DRK MTLC REPLACMNT PK,BELTONE 62,TRANSP REPLACMNT PK,BELTONE 62,PURPLE REPLACEMENT PK,BELTONE 62,BLUE REPLACEMNT PK,BELTONE 62,BLACK * These replacement packs are nano coated Page 8 of 22
9 Power Dome Tool Power Dome Tool Prepare a HF3 tool with HF3 Insert HF3 tool with HF3 all the way in the power dome until it passes through the rectangular cavity of the power dome Place the longer length of the rectangular cavity of the power dome over the Power Dome Tool. Ensure that the Power dome is installed on the Power Dome Tool by checking it and it is flushed even with the tool as shown (3rd pic) Squeeze and hold bottom of the Power Dome Tool to open the Power Dome rectangular cavity. Insert the HPG Receiver, with the longer length of the receiver parallel to the longer length of the rectangular cavity of the Power Dome As the HPG receiver is pushed into the Power Dome, carefull pull out the Power Dome Tool Page 9 of 22
10 Exploded View Mic Cover Top Housing Battery door Battery Receiver Tube Mic Gasket Microphone Programming contacts Sport lock O ring Hybrid C3.1 Mic Frame Hinge pin Battery Contacts Bottom housing Page 10 of 22
11 Wiring Diagram ( -) (+) RECEIVER C3.1 C3.1 HYBRID H3 H2 (+) (0) (-) FRONT MIC MIC H13 H10 H1 (-) (+) BATT CONTACTS CONTACTS H11 H12 H16 H15 H6 H4 H5 (+) (0) (-) BACK MIC BACK MIC Note: Apply coat material after soldering on connections PROGRAMMING PINS PINS Page 11 of 22
12 Mic Cover Removal Support Align the blade part of the removal tool onto the slot between mic cover and the top housing Insert the blade part of the removal tool onto the slot between mic cover and the top housing Supporting the other end of the mic cover while lifting the other end with the removal tool pressed downwards to release the mic cover from the top housing Removal Tool p/n Page 12 of 22
13 Battery & Battery Door Removal Battery Removal Open the battery door, until ends of door touches the housing Roll off the top portion of the battery Slowly remove battery from the device Battery Door Removal Open the door halfway Hold door firmly with thumb and index finger Hold door firmly and slowly rotate the device to release the door from the hinge Remove door from the device Page 13 of 22
14 Housing Removal Size 13 and 312 Size 10 Align the slot part of the removal tool onto the hinge pin Hold side of the device while pressing the front of removal tool as arrow indicated on removal tool. Do not place a finger at the bottom of the device while pushing down the frame assembly with the tool Once the removal tool is pushed down, the bottom housing will be released from the top housing Separate the bottom housing frame assembly from the top housing Page 14 of 22
15 Adding New Colour/ Replacing Housing Batt door Mic cover Bottom housing frame assembly Receiver Tube Get new desired colour or replacement housing, door, mic cover & receiver tube and add it on the bottom housing frame assembly Insert bottom housing assembly horizontally into housing. Ensure the nose part of the assembly is centered when inserting bottom assembly Push round end of bottom housing assembly into housing until it clicks Add batt door, receiver tube and mic cover to complete unit Page 15 of 22
16 Microphone Replacement Slide out the mics (front or rear) from white frame Desolder old mic wires and solder onto replacement Rear Mic Add Loctite 420 or similar Front Mic Rear Mic Front Mic Rear Mic Front Mic Mic gaskets Glue mic gaskets on mics using Loctite 420 or similar Install mic on white frame Note: Apply coat material after soldering on connections Page 16 of 22
17 Test Equipment Coupler Insert to be used for final HI test p/n Either of the shown 2cc coupler inserts must be used for rec test. Both inserts can be ordered with GTO Dept in HQ. More info to be found on GTO website under DSA6000 Documentation Batt pill 10A must be used during test p/n Test Fixture p/n Test Rec Tube NP p/n Rec Tube connector Note : Fixture does not come with test rec tube. It has to be ordered. Rec tube can be replaced as needed Prog cable CS63 (3 pin) Flex strip Connect the flex to the prog cable by using the flex end marked with an arrow Flex strip Prog cable CS63 p/n Flex strip for CS63 p/n (10 pcs pack) 2cc coupler p/n to be ordered with GTO Dept/HQ Ballerup DK Page 17 of 22
18 Testing Protocol for HPG and MPG Devices For HPG Device only: Capture current customer settings in Solus. It is usually defaulted to Open settings. Even though this is a HPG, connect to MPG test fixture as described on page 21. The HPG device is only tested in MPG parameters with MPG receiver. Proper programming cable and battery pill are required. Run correct model TPI. If test failed, repair and run test again. If test passed, recall saved customer settings from Solus and ship back to customer. Important Note: The device will remain MPG device until the previous customers settings from Solus are restored and using HPG receiver to connect to the device, would revert the device back to being HPG Device. Failure to do so would compromise the output of the device. For more detailed test procedure see page 21. For HPG Receiver only: Connect the HPG receiver tube on a known good device. Properly place the assembled device in the sound chamber of test machine to test. Proper programming cable and a fresh battery are required. See page 22 for reference. Run the HPG receiver TPI If test failed, needs to be replaced. If test passed, print test result and ship back to customer. For MPG Device only: Capture current customer settings in Solus. Connect device on the MPG Test Fixture (see page 19).Proper programming cable and battery pill are required. Run correct model TPI. If test failed, repair and run test again. If test passed, recall saved customer settings from Solus and ship back to customer For more detailed test procedure see page 21. For MPG Receiver only: Connect the MPG receiver tube on a known good device. Properly place the assembled device in the sound chamber of test machine to test. Proper programming cable and a fresh battery are required. See page 23 for reference. Run the MPG receiver TPI If test failed, needs to be replaced. If test passed, print test result and ship back to customer. Page 18 of 22
19 Testing Device using Test Fixture Gap for strain relief No Mic cover Connect device to MPG rec tube connector. Mic cover should not be on device when testing Properly oriented device on Receiver Tube connector Connect coupler insert to the rec tube. Ensure that there is small gap between the insert and rec tube for strain relief Not oriented properly on Receiver Tube connector Attach prog cable and battery pill. Position the fixture with hearing instrument as shown in the test chamber, with the mic hole facing the speaker. Run MQ17 / MQ9 TPI test Gap for strain relief No gap Correct Placement on Fixture Wrong Placement on Fixture Page 19 of 22
20 Testing HPG Receiver Tube only Position the fixture with hearing instrument as shown in the test chamber Remove dome attached from HPG rec tube (if any) Connect the HPG rec tube to a known good MQ17 / MQ9 device Wrap blue putty around the HPG rec tube. Be careful not to block the opening of the rec Insert the HPG rec with a blue putty wrap to the coupler insert. Do not let any part of the rec..touch the coupler insert. Push the back end of the rec in the center hole of the insert until the..front end of the rec is flushed to the backside opening of the insert Place a fresh battery and connect flex programming cable to the device Connect the coupler insert to the AUDIOMaster microphone Run HPG Receiver TPI test Page 20 of 22
21 Testing MPG Receiver Tube only First attach the receiver to a known good Marq hearing instrument, do not use the returned hearing instrument to verify the receiver. Any new Marq hearing instrument in inventory could be used. Connect cable and fresh battery to device and correct coupler Position the device approximately vertically in the middle of the box. Be sure that point where the tube and hearing aid meets is positioned above calibrated spot (middle of the green circle inside the test box). Do not try to lean the device on the coupler. Close the sound chamber and run MPG Receiver TPI Page 21 of 22
22 Receiver Tube Replacement on Test Fixture When replacing Receiver Tube, be sure to attach it to a device before screwing down the Top Plate of the fixture. This will help ensure the connector is oriented properly Do not replace Receiver Tube by itself. This may lead to an improperly oriented connector Page 22 of 22
Technical Manual Beltone Paris Platform BTE
Technical Manual Beltone Paris Platform BTE Global Technical Operations gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@Beltone.com Table of Contents Form-Factor-Matrix...3 Colour
More informationTechnical Manual ReSound Match ITC. GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark
Technical Manual ReSound Match ITC GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@gnresound.dk Table of contents Subject Page Matrix... 3 Spare Part List...
More informationTechnical Manual ReSound Match ITE. GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark
Technical Manual ReSound Match ITE GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@gnresound.dk Table of contents Subject Page Matrix... 3 Spare Part List...
More informationTechnical Manual INT START BTE. Global Technical Operations gto.gnresound.com Lautrubjerg 7 DK-2750 Ballerup Denmark
Technical Manual INT START BTE Global Technical Operations gto.gnresound.com Lautrubjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@gnresound.dk Table of Contents SA70 & SA70-D: Page Description... 3 Part
More informationTechnical Manual ReSound Metrix MX70-D/DI/DV/DVI/ MX80-DVI BTE
Technical Manual ReSound Metrix MX70-D/DI/DV/DVI/ MX80-DVI BTE GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark E-mail: Service@gnresound.dk Table of
More informationBeltone A/S Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark. Technical Manual Beltone DELHI Platform
Beltone A/S Global Technical Operations http://gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark Technical Manual Beltone DELHI Platform Table of Contents Form-Factor-Matrix & Product information...
More informationTechnical Manual ReSound TrimFlex ITC
Technical Manual ReSound TrimFlex ITC GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@gnresound.dk Table of Contents Description...3
More informationACS75, ACS75D, ACS85 & ACS85D BTE Overview. GTO September 2006 / May 2007
ACS75, ACS75D, ACS85 & ACS85D BTE Overview GTO September 2006 / May 2007 ACS75 & ACS75D ACS75 ACS75D Disassembly Pull out the soundhook from the BTE housing. Disassembly Squeeze to grip Open the battery
More informationTechnical Manual Canta 770-D/470-D & 270/270-D
Technical Manual Canta 770-D/470-D & 270/270-D (including 770-D & 470-D Open BTE features) GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark Phone: + 45
More informationTechnical Manual EDGE E65 Mini-BTE
Technical Manual EDGE E65 Mini-BTE Global Technical Operations gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark Phone: + 45 45 75 2 6 E-Mail: Service@Beltone.com Table of contents Description...
More informationTechnical Manual Pixel Mini BTE PL60-DI
Technical Manual Pixel Mini BTE PL60-DI GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 7-11 DK-2750 Ballerup Denmark Phone: + 45 45 75 23 16 E-mail: Service@gnresound.dk Table
More informationUNCONTROLLED COPY IF PRINTED. Service Information
Service Information This document has been produced for the service departments of the Unitron Hearing group companies and agents. It is reserved for Unitron Hearing Service Centers and for trained, authorized
More informationTechnical Manual Canta 730/ /230 VC & Canta 730-OC/430-OC 730-D ITC
Technical Manual Canta 730/430 230/230 VC & Canta 730-OC/430-OC 730-D ITC GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark Phone: + 45 45 75 23 16 E-Mail:
More informationBPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
BPL SERIES INSTALLATION INSTRUCTIONS Important Warning THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This product must be installed in accordance with National Electrical
More informationipod Classic Headphone Jack & Hold Switch Replacement
ipod Classic Headphone Jack & Hold Switch Replacement Replace Headphone Jack & Hold Switch to fix no audio and/or no unlock Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION
More informationTechnical Manual. RS LONDON Platform. ReSound A/S Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark
Technical Manual RS LONDON Platform ReSound A/S Global Technical Operations http://gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark Table of Contents Form-Factor-Matrix & Product Information...
More informationInstallation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2
1 Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2 Tsubis Part Number: LCD12-0046 Power Down 1. Power down the controller. 2. Power down the complete machine by turning off the rear
More informationUpgrade Instructions. P/N Revision A. October Printer Terminal Holder * *
Upgrade Instructions P/N 96-08-0 Revision A October 000 480 Printer Terminal Holder P/N 96-08-0 Revision A *96080* Instructions This terminal holder connects the INTERMEC R 600 Series and 700 Series Computers
More informationEncore XT Manual Gun Upgrade Kit
Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.
More informationCONEC Industrial Ethernet Circular Sealed RJ45 Connector System consists of a RJ45 Plug Kit, a Receptacle Kit and a Protective Cover Assembly.
Revised Sept-28-2009 Sealed Industrial Ethernet Circular IP67 Cat. 5e RJ45 Connector System Instructions CONEC Industrial Ethernet Circular Sealed RJ45 Connector System consists of a RJ45 Plug Kit, a Kit
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationFuser. Figure Remove the fuser assembly (1 of 2) 184 Chapter 5 Removal and replacement ENWW
Fuser 1. Remove the following assemblies. Scanner assembly. For the HP LaserJet 3015, see Scanner assembly. For the LaserJet 3020 and 3030, see Scanner assembly. Left cover. See Printer side covers. Rear
More informationOnePlus 5 Screen and Digitizer Assembly Replacement
OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:
More informationMicrosystems. SCI-6 Sound Card Interface Kit Version 1.09 January 2015
UM Unified Microsystems SCI-6 Sound Card Interface Kit Version 1.09 January 2015 The SCI-6 interface was designed to be a low cost, high quality interface between your PC s sound card and radio transceiver.
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationChapter 4 Replacement Procedures
Chapter 4 Replacement Procedures 4 4-ii Satellite P30 Series Maintenance Manual Chapter 4 Contents 4.1 General... 4-1 4.2 Battery... 4-7 4.3 PC Card... 4-8 4.4 HDD... 4-10 4.5 Optical Drive Module... 4-12
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationipod Classic Battery Replacement Replace the battery on your ipod classic. Written By: irobot ifixit CC BY-NC-SA
ipod Classic Battery Replacement Replace the battery on your ipod classic. Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Battery not lasting long? Swap it out. TOOLS: 1.5"
More information120/220 Magazine HM401
120/220 Magazine HM401 English Instructions Battery The button battery supplies power to the magazine s LCD when it is not attached to the camera. When the magazine is attached to the camera, power is
More informationipod Touch 4th Generation 30 Pin Dock Connector Replacement
ipod Touch 4th Generation 30 Pin Dock Connector Replacement Learn how to replace the 30 pin dock connector on an ipod touch 4th generation. Written By: Gabe Keehn ifixit CC BY-NC-SA www.ifixit.com Page
More informationWritten By: Sam Lionheart
iphone 5s Lightning Connector Replacement Remove the Lightning connector/headphone jack assembly from your iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION
More informationww.battery-adapter.com
Removing and replacing an FRU Lenovo G470/G475/G570/G575 This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general
More informationipod Classic Click Wheel Replacement Written By: irobot ifixit CC BY-NC-SA Page 1 of 25
ipod Classic Click Wheel Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION The click wheel receives the feedback of your fingers and transmits it to the logic board.
More informationDell Latitude C800 Service Manual
Dell Latitude C800 Service Manual Dell Latitude C800 Service Manual Before You Begin Preparing to Work Inside the Computer Recommended Tools Screw Identification Removing and Replacing Parts System Components
More informationPERFECT HANDLING. PCB Front Panels & Injector/Extractor Handles... Package Your Electronics With Ripac.
Front Panels & Injector/Extractor Handles... PERFECT HANDLING. Package Your Electronics With Ripac. When it comes to electronics, no one handles today s demanding applications better than Rittal Ripac
More informationDanalock V3 SCANDI Mounting guide.
Danalock V3 SCANDI Mounting guide www.danalock.com Table of contents Tools needed page 4 Parts involved page 5 1. Secure the front lock page 6 2. Remove the inside thumb-turn page 7 3. Normal tailpiece
More informationInstalling a Power over Ethernet injector
Installing a Power over Ethernet injector AlphaEclipse StreetSmart and RoadStar signs The instructions in this document explain how to install/replace a Power over Ethernet (PoE) injector in a StreetSmart
More informationWhen you are ready to build your computer you will have the following materials to work with.
Copyright 2009 BOSMA Enterprises Chapter 3 Putting the Computer Together When you are ready to build your computer you will have the following materials to work with. 1. One motherboard. 2. One ribbon
More informationWritten By: Sam Lionheart
iphone 5s Earpiece Speaker Replacement Replace the earpiece speaker in an iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Use this guide to replace a broken
More informationFitting range
P R O D U C T I N F O R M A T I O N Fitting range HL - 0 CIC/MIC ITC ITE/ITE D ITE P (312) BTE/BTED/ ITE P (13) BTE P 125Hz 2 0 0 00 00 00 Product Concept Atlas Plus offers a full family of high quality
More informationReplacing the SATA PCI Controller Card
Replacing the internal controller PCI card may be performed by a single administrator; no tools are necessary. Caution There are static-sensitive electronics inside the unit. Before you handle any parts,
More informationRemoval and Installation 8
Removal and Installation 8 8 Introduction 8-2 Service Calibration Guide to Removal and Installation 8-4 Window 8-8 Covers and Trims 8-12 Rear Tray 8-31 Rear Cover 8-32 Media Lever 8-33 Media Lever Position
More informationDIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL
DIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL Version 2.1 June 4, 2013 0 Table of Contents Low Profile Pan Tilt Kit Description... 3 Low Profile Pan Tilt Unit Basic Operation... 4 Mounting
More informationPanasonic Toughbook CF-29 Motherboard Replacement
Panasonic Toughbook CF-29 Motherboard Replacement Written By: Dylan Bloom ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION This guide will tell you how to gain access to and remove the motherboard.
More informationTOYOTA SIENNA Dual Headrest Video
TOYOTA SIENNA 2011- Dual Headrest Video Part Number: 00016-08130; Bisque 00016-08135; Gray 00016-08140; Dark Charcoal Code: EH5 Conflicts: Color Applicability/ Trim Level: Kit Contents: Item # Qty. Component
More informationReplacement Instructions. Backplane PCA for the HP Router 650
Replacement Instructions Backplane PCA for the HP Router 650 Copyright Hewlett-Packard Company 1994. All rights reserved. Publication Number 5962-8369 Edition 1, August 1994 Printed in USA This guide provides
More informationPowerBook G4 Aluminum 12" GHz Display Data Cable Replacement
PowerBook G4 Aluminum 12" 1-1.5 GHz Display Data Cable Replacement Written By: Matthew Newsom ifixit CC BY-NC-SA www.ifixit.com Page 1 of 47 INTRODUCTION Replace a damaged display data cable to restore
More informationiphone 6 Plus Front Facing Camera and Sensor Assembly Replacement
iphone 6 Plus Front Facing Camera and Sensor Assembly Replacement Replace the Front-Facing Camera and Sensor Assembly in your iphone 6 Plus. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page
More informationA-dec 570L Dental Light on a DCS System INSTALLATION GUIDE
A-dec 570L Dental Light on a DCS System INSTALLATION GUIDE C ONTENTS Choose an Installation Guide...... Before You Begin.............. 3 Disconnect the Light Cable........ 3 Cut the Light Cable............
More informationInstallers & User guide Deadbolt 2S.
Installers & User guide Deadbolt 2S. Version 0.2 05/18 As our igloohome app is frequently updated, there may be changes to this manual. Please refer to our website igloohome.co/support for the latest version
More informationitech Training Courses iphone 5S LCD Assembly Replacement Guide
itech Training Courses iphone 5S LCD Assembly Replacement Guide 2014 icracked, Inc. All rights reserved. ios, all Apple product names, and Apple logos are trademark property of Apple, Inc. The content
More information4.1 General. 4 Replacement Procedures
4.1 General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is
More information6 Removal and replacement
6 Removal and replacement This chapter contains information about the following topics: Removal and replacement strategy User-replaceable parts Covers and external components Main assemblies Motors and
More information3M Add-On Terminals 4220P (100, 200, 300 & 400 pairs)
3M Add-On Terminals 4220P (100, 200, 300 & 400 pairs) Instructions August 2011 3 78-8130-2330-1-C 1.0 General 1.1 The 3M Add-On Terminals 4220P-100, 4220P-200, 4220P-300 and 4220P-400 are designed to expand
More informationOLPC XO-4 Touch Mouse Buttons Controller Replacement
OLPC XO-4 Touch Mouse Buttons Controller Replacement This guide will show you how to replace the mouse buttons controller. Written By: Michael Kellerman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION
More informationINSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,
More informationInstallation Guide. Copyright 2005 MSI Computer Corp.
Installation Guide Copyright 2005 MSI Computer Corp. Overview: 1013 is shipped out as a barebone. Some of the components are equipped while some are not. This installation guide provides you with the information
More informationReplacement Keyswitch Assembly
Installation Instructions Replacement Keyswitch Assembly (Catalog No. 2711E-NKSW1) Applicable Terminals Use this replacement keyswitch with PanelView Terminals 2711-KA1, -KC1, -TA1, -TC1, -TA4, -TC4 and
More informationWelch Allyn Connex Vital Signs Monitor 6000 Power Supply Replacement
Welch Allyn Connex Vital Signs Monitor 6000 Power Supply Replacement Replace the power supply in a 6000 series Welch Allyn Connex Vital Signs Monitor. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com
More informationipad Mini Wi-Fi Front Facing Camera Replacement
ipad Mini Wi-Fi Front Facing Camera Replacement Replace the Front Facing Camera in your ipad Mini Wi-Fi. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 42 INTRODUCTION
More informationUNCONTROLLED COPY IF PRINTED. Service Instruction. Shine Rev M
Service Instruction Document Number: This document is produced and reserved for Unitron service centers and for trained authorized service departments exclusively. : Electrostatic discharge sensitive devices
More informationCanon EOS Rebel T2i Top Cover Replacement
Canon EOS Rebel T2i Top Cover Replacement Replacing the top piece of a Canon T2i (550D). In my case, I had a broken hot-shoe, but as most controls on this camera are built into the same part, this repair
More informationPowerBook G4 Aluminum 17" GHz Heat Sink & Fan Assembly Replacement
PowerBook G4 Aluminum 17" 1-1.67 GHz Heat Sink & Fan Assembly Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION The heat sink and fan together help to keep the
More informationHow To Install: C4000 EMV Upgrade Kit
How To Install: C4000 EMV Upgrade Kit IMPORTANT: Before proceeding with installation please verify you have the current card reader bezel in the kit. Correct bezel will have a small eject pin hole below
More informationPowerBook G4 Aluminum 12" GHz Left Clutch Hinge Replacement
PowerBook G4 Aluminum 12" 1-1.5 GHz Left Clutch Hinge Replacement Written By: Matthew Newsom ifixit CC BY-NC-SA www.ifixit.com Page 1 of 50 INTRODUCTION Replace a broken clutch hinge to make your display
More informationProduct Information NANO
Product Information NANO Nano is a hearing aid, suitable for users with a wide range of hearing losses. Nano features the Audina proprietary Audio Efficiency technology that incorporates first-class features
More informationibook G3 14" Hard Drive Replacement
Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 20 INTRODUCTION How to remove the hard drive and its bracket from your computer. TOOLS: Coin (1) Paper Clip (1) Phillips #00 Screwdriver (1)
More informationibook G4 12" 800 MHz-1.2 GHz RJ-11 Board
ibook G4 12" 800 MHz-1.2 GHz RJ-11 Board Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 24 INTRODUCTION The standard telephone jack port for connecting to the 56k internal modem.
More informationInstallation Instructions
Installation Instructions Phones, Navigation These Installation Instructions supersede those dated February 2004. Page 1 of 9 March 2004 Accessory Development Changes to this revision are identified by
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationMotorola Atrix 4G Bottom Speaker
Motorola Atrix 4G Bottom Speaker Replacement This guide will show you how to access the Motorola Atrix 4Gs bottom speaker for repair or replacement. Written By: Jake ifixit CC BY-NC-SA www.ifixit.com Page
More informationipad mini 4 LTE Screen and Digitizer Replacement
ipad mini 4 LTE Screen and Digitizer Replacement Replace the fused LCD screen and digitizer in an ipad mini 4 LTE. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Follow
More informationMounting Accessory Guide
Apr. 12 2010 Table of Contents Mounting Accessory Guide 1 Overview 5 Introduction... 5 Types of Mounting Methods... 5 Surface... 5 Wall... 5 L-Type Wall Mount (PMAX-0308) 6 Heavy Duty Wall Mounts (PMAX-0305
More informationRECORD & PLAYBACK KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT Version 2.1 Build Instructions
More informationAg Leader Technology Insight. Direct Command Installation Spra-Coupe 7000 Series
Note: Indented items indicate parts included in an assembly listed above. Part Name / Description Part Number Quantity Direct Command Spra-Coupe 7000 Kit 4100531 1 Liquid Product Control Module 4000394
More informationApex Tablet 7 Battery Replacement
Apex Tablet 7 Battery Replacement This guide will instruct you on how to replace the lithium-ion battery inside the Apex 7" Tablet. Written By: Corrine Nief ifixit CC BY-NC-SA www.ifixit.com Page 1 of
More informationWritten By: John Sutton
Replacing the fan on your HP g7-2275 dx. Written By: John Sutton ifixit CC BY-NC-SA www.ifixit.com Page 1 of 20 INTRODUCTION Laptop cooking your lap? This guide will walk you through replacing your fan.
More informationWINSTA. Full Line Catalog 2008/2009
WINSTA Full Line Catalog 2008/2009 5 Contents FULL LINE CATALOG W4, Volume 1 Rail-Mounted Terminal Block Systems FULL LINE CATALOG W4 Rail-Mounted Terminal Blocks Volume 1 X-COM -SYSTEM Terminal Strips
More informationLASERJET ENTERPRISE M604, M605, M606
LASERJET ENTERPRISE M604, M605, M606 Maintenance kit replacement manual M604n M604dn M605x M605n M605dn M606x M606dn Conventions used in this guide TIP: Tips provide helpful hints or shortcuts. NOTE: Notes
More informationUpgrading LVDS Cables Instruction Sheet
Upgrading LVDS Cables Instruction Sheet INTRODUCTION Use the following instructions to replace the LVDS cables in CP2000-M/MR projectors. The new cables are slightly longer in length and allow for better
More informationReplacing the Power Supply
APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools
More informationRedigido por: Sam Lionheart
ipad Mini 2 Wi-Fi Microphone Replacement Replace the dual microphone in the ipad Mini 2 Wi-Fi. Redigido por: Sam Lionheart ifixit CC BY-NC-SA pt.ifixit.com Página 1 de 36 INTRODUÇÃO Use this guide to remove
More informationMacBook Pro 17" Models A1151 A1212 A1229 and A1261 Display Inverter Replacement
MacBook Pro 17" Models A1151 A1212 A1229 and A1261 Display Inverter Replacement Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION Backlight not working? Use this guide
More informationSOLO an invisible, electronic lock with multiple usages STAND-ALONE ELECTRONIC RFID LOCK FOR:
SOLO an invisible, electronic lock with multiple usages STAND-ALONE ELECTRONIC RFID LOCK FOR: Shops and Retail: Hospitals: Offices: Schools: Clubs: Glass cabinets and display cases, supply cupboards, staff
More informationOLPC XO-4 Touch Touchpad Controller Replacement
OLPC XO-4 Touch Touchpad Controller Replacement This guide will walk through replacing a touchpad. Written By: Theodore Tsanakas ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION Use this guide
More information2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual
2015 SIMMCONN LABS, LLC. All rights reserved NewScope-T1 Operation Manual April 12, 2017 NewScope-T1 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1 Initial Inspection... 4 2.2 Installation
More informationipad Mini 2 Wi-Fi Front Panel Assembly Replacement
ipad Mini 2 Wi-Fi Front Panel Assembly Replacement Fix a broken ipad Mini 2 screen. Replace the front glass and digitizer on an ipad Mini 2 Wi-Fi. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationReplacement Instructions
imac G5 Inverter, 20-inch Replacement Instructions Follow the instructions in this document carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note: Online
More informationME PLC Multifunctional housing for complex electronics. Data sheet _en_01. 1 Description
Multifunctional housing for complex electronics Data sheet 105504_en_01 PHOENIX CONTACT 2013-04-08 1 Description The housings of the ME PLC 40... product group consist of a 40-mm wide housing base with
More informationTONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP LASERJET 4600 TONER CARTRIDGE
HP LASERJET 4600 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP LASERJET 4600 TONER CARTRIDGE REMANUFACTURING THE HP LASERJET 4600 TONER CARTRIDGE By Javier Gonzalez and the Technical Staff at UniNet
More informationBehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer SRC analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND
ASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND E062324 ELO-STAND-SELF-SERVICE-DESKTOP E062510 ELO-STAND-SELF-SERVICE-FLOOR EXT E062704 KIT-EMV-CRADLE-VF-MX915-ING-ISC250 E062899 KIT-EMV-INGENICO IPP350
More informationLED. Sign Module. Assembly Manual
LED Sign Module Assembly Manual 6/14/2002 3:10 PM 6 2 3 3 E. S a w g ra s s R d S a ra s o ta, F L. 3 4 2 4 0 (9 4 1 )3 7 7-5 7 7 5 F A X(9 4 1 )3 7 8-4 2 2 6 www.acscontrol.com Table of Contents Table
More informationDell Latitude C800 SERVICE MANUAL. support.dell.com
Dell Latitude C800 SERVICE MANUAL www.dell.com support.dell.com Dell Latitude C800 SERVICE MANUAL www.dell.com support.dell.com Notes, Notices, and Cautions NOTE: A NOTE indicates important information
More informationFDS / FDS-R / FDS-PS
FDS / FDS-R / FDS-PS USER MANUAL For use with 120V 60Hz input. Output is 120V 60Hz at 5amps 600W MAX. switched. ETL LISTED Conforms to UL STD 1241 3091594 79-15167-00 REV. A www.fiberstars.com Page 1 of
More informationMotorola Droid X Camera Replacement
Motorola Droid X Camera Replacement Written By: Gage ifixit CC BY-NC-SA www.ifixit.com Page 1 of 24 TOOLS: 64 Bit Driver Kit (1) ifixit Opening Tools (1) ifixit CC BY-NC-SA www.ifixit.com Page 2 of 24
More informationMac Mini Model A1176 SSD Dual Drive
Mac Mini Model A1176 SSD Dual Drive Installation Trade your optical drive for a second hard drive. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 16 INTRODUCTION Use this guide to trade your
More information2 PIECE BOARD-TO-BOARD
2 PIECE BOARD-TO-BOARD 201-01-123 1. SPECIFICATION DISTRIBUTION No restrictions for issue 2. SCOPE This specification contains the application notes for the 9159 two part connectors. 3. PRODUCTS 10-9159
More informationZune Flash 2nd Generation Battery and Memory Board Replacement
Zune Flash 2nd Generation Battery and Memory Board Replacement Written By: killdashnine ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION This will serve as a guide for the replacement of a Zune
More information